Cosmetics: The amplifier is gray and it has a black, removable metal shroud. Though this is one 4-channel amplifier, Kicker uses the terminology of "Amp 1" and "Amp 2" to indicate the channels.
Amplifier Shroud: The amplifier has a metal shroud that must be
removed before installation, allowing access to the amplifier's inputs and outputs. Once the amplifier is installed and all the connections are made, you can re-install the shroud to hide the connections on the amplifier, or leave the shroud off to save space. With the shroud removed, the amp has
the following dimensions: W=12.4375" (14.375" with RCA's) x H=2.355" x D=9.535".
Kicker "Living Loud" Certified Power Certificate: The amplifier comes with a certificate that informs you of the total maximum wattage of the particular amplifier, along with the model number, serial
number, tested date, and whether the amplifier passed the total harmonic distortion, signal-to-noise ratio, and protection circuit tests (if it shipped, you can count on it passing these tests).
Speaker-level Inputs: Two high-level input connections are included to allow use with
sources that do not have RCA preamp level outputs. When using both sets of High Level Inputs, use the dummy RCA plugs and plug them into the RCA inputs of "AMP 2" in order for the fader to work properly.
Built-in Variable Electronic Crossovers: There are two built-in crossovers that
allow you to select high-pass for satellite speakers, low-pass for subwoofers, or bypass for full-range operation. The crossover frequency is variable from 50 to 200Hz.
SORT (Short circuit, Over-voltage, Reverse polarity, Thermal) Protection Circuitry: The SORT protection circuitry
guards against accidents and undesired operation. The Power LED on the left side of the amp glows green and the power indicator on top of the amp glows red when the amplifier is connected correctly and SORT has not been engaged. If the red Protection LED illuminates, SORT has been engaged and the
amplifier is in protect mode until the problem is resolved.
KickBass Bass Boost: The two KickBass bass boost circuits provide up to 18dB signal boost at 40Hz.
SAMS (Stereo And Mono Simultaneously): With a Tri-mode adapter (item # 127TM100), this amplifier can run four
satellite speakers and two subs at the same time.
Controls
Top of Amplifier:
•KickBass Bass Boost Control for Amp 2: rotary control, boosts the bass at 40Hz from 0 to +18dB
•Gain Control for Amp 2: rotary input gain control, 170mV-5V line level,
340mV-10V speaker level
•Variable Crossover Frequency Control for Amp 2: adjustable from 50-200Hz
•KickBass Bass Boost Control for Amp 1: rotary control, boosts the bass at 40Hz from 0 to +18dB
•Gain Control for Amp 1: rotary input gain control, 170mV-5V line level, 340mV-10V
speaker level
•Variable Crossover Frequency Control for Amp 1: adjustable from 50-200Hz
Right Side of Amplifier:
•Amp 1 Crossover Mode Switch: Hi Pass, Lo Pass, or Off
•Amp 2 Crossover Mode Switch: Hi Pass, Lo Pass, or Off
Inputs and Outputs
Left
Side of Amplifier:
•12+ (power): gold-plated screw terminal (terminal is 0.308" wide)
•REM (remote turn-on): gold-plated screw terminal (terminal is 0.218" wide)
•GND (ground): gold-plated screw terminal (terminal is 0.308" wide)
•Fuse: two 20-amp fuses
Right Side of Amplifier:
•Amp 1 Speaker Output: gold-plated screw terminals (each terminal is 0.210" wide)
•Amp 1 High Level Input: Molex plug input for included harness
•Amp 2 High Level Input: Molex plug input for included harness
•Amp 1 RCA Input: gold-plated
RCA line input jacks
•Amp 2 RCA Input: gold-plated RCA line input jacks
•Amp 2 Speaker Output: gold-plated screw terminal (each terminal is 0.210" wide)
Specifications
Power Rating:
•4-Ohm Stereo: 60 watts RMS x 4
•2-Ohm Stereo: 90 watts RMS x 4
•4-Ohm Stereo Bridged: 175 watts RMS x 2
Внимание! сейчас Вы не авторизованы и не можете подавать сообщения как зарегистрированный пользователь.
Чтобы авторизоваться, нажмите на эту ссылку (после авторизации вы вернетесь на
эту же страницу)
